ok issue resolved. got a call from definedge team. may be some technical glitch

sorry earlier repeated tradepoint chart

Hi

I am opening Chart of GMR Infra in 0.25 % PNF

in Rzone chart is showing column Reversal on 01.12.2023 (today)

Tradepoint

Rzone

Does plotting on PF charts has any specific use i any strategy or scanner?

Flat bands will show that both numerator and denominator are equally performing or underperforming

Rising bands- numerator is outperforming
Falling bands- denominator is outperforming

posting some suggestion for auto trade engine

1. while running multiple strategies, i observed that if want to change something in some strategy in between (e.g if i am trading in 2 lots per position and i want to change to 1 lot per position), i cannot edit that. I have to first close the engine (while other strategies are running), delete the strategy and again open new strategy and then again go to ultra scanner to restart. Meanwhile while i am doing this , i have to stop ALL strategies. So pls correct it so that it can be edited strategywise without stopping the whole engine.

2. Earlier also i have queried this to allow maximum position in total strategy. E.g i want 5 positions in the day. Now, it happens as soon as one of the positions squared off, i get new position from signal which i dont want. If I stop the engine after 5 positions, i will not be able to square off automatic.

3. Mentioned in telegram group earlier, make the engine consistent with back testing to allow execution of trades after pattern lock. Prashant sir has replied that it is difficult and will do something about it. Because what i backtest in any time frame, i must be able to execute that in auto trade.

4. Pls allow source code and cash market share and execution in futures different expiry. e.g on expiry day i want to see turtle breakout in infy cash , andu buy infy next month future as i dont want to buy same month on expiry day.

5. There is requirement of group selection twice. Once in main engine and again the same group in ultra scanner. This repetition can be avoided. Although it created no difficulty.

6. Suppose in Auto trade main engine , i select Long. Now, in Ultra scanner i select Short position and signal for short comes, order of BUY is executed. although it is our mistake to select buy in auto trade and sell in ultra scanner, it should show error

7. Allow time base exit, e.g if i buy and if target achieved then ok otherwise sell at 2.00 pm, 1.00 pm as per choice.

Thanks
Sumit Badwani
9827400290

1. No, it will be around 50 wk high as it would consider trading days only excluding holidays
2. Bullish is over upper band and bearish below lower band
   3.yes, as we are using in DON 28 brick high

1. Gap between 20 day high low is reducing and consolidating, formation of nr4 and nr7 may be there. May be volatility about to expand
2. Depends on brick size, short term long consolidation. Not sure
3. Range expansion, high volatility, w7 formations
4. 20 brick high and 20 brick low

Hi,

I observed today that buzzar starts in preopen session. As it is signal for buying and selling for us, it is of no use in preopen. Kindly update the platform to start at 9.15 as soon as actual market starts.

Signals should come at start of market and thereafter only

thanks
Sumit Badwani

HI

When i am backtesting in Rzone, there is option to export file in excel in TRADE DETAILS. I think if the file is large i.e if higher no of trades, i am not able to export and Rzone exits itself.

Please inform if there is any such restriction in exporting. If there is any such restriction, please remove such restriction if possible

Thanks
Sumit Badwani
7000835650
[email protected]

HI
I have observed that when i backtest in Rzone for short period say one month. e.g Buy at AFT bullish and sell at DBS or High Pole.

When i run backtest , the results show only stocks which are squared off during the month e.g if there are total 50 AFT bullish signals and 20 are squared off. Postions (signals) which are squared off (20) will be shown in backtest. The position of balance 30 positions do not come in backtest.

e.g if profit target is hit in 20 signals and remaining positions are at loss, the backtest result will show 20 trades will all profits and high expectancy rate and average return per trade and 100 percent success rate.

Whereas my balance positions are 30 which may be at loss (as exit signal not came).

So, please if possible please add additional column in backtest which show outstanding signals(positions) which are not squared off during the period of backtest

Thanks
Sumit Badwani

Please try to add following features in Autotrade Engine

1. Only Buy : If i want to buy only using autotrade engine and dont want to sell on same day. e.g If i want to buy stock futures which have made Turtle breakout bullish in the day with maximum 10 positions and dont want to sell today.

2. Only Sell : Same for only sell

3. Stop loss : e.g If i have 10 stocks in my portfolio and i want to sell them whenever DBS signal is there, i would put in group and set double bottom signal and whenver there is double bottom sell signal during the day stock will be automatically sold. I dont have that facility now.

4. Maximum Positions : There is option of maximum positions. Suppose i want to take maximum 5 positions for the day. Currently, what happens is whenever i reach 5 positions and there is exit in one of the positions as per signal, the engine looks of next position. It takes 6 th position which i dont want. Suppose , for this i stop the engine after 5 positions, it will not square off my postion as per exit signal. So Please add maximum day positions so that 6th position is not taken by engine and it continues to square off existing positions.

5. Jobbing : Suppose i use engine in options and i start engine at 9.15. Since the order executes at market, if there is jobbing e.g price is 8.15-10.50 which happens quite often in options, i end up buying at 10.50 which is unreasonable price. Please add some solution to this e.g limit order or make first buyer/seller or any other probable solution. Because there is huge loss in purchase in this case.

6. Please allow for carrying the position if not squared off in the day. Currently, if signal does not come , all positions are squared up (i think on 3.20 or 3.10 pm)

Thanks
Sumit Badwani

I think it is available in groups we can select My Groups which is displaying our groups